Left joy con joystick replacement

Left joy con joystick replacement DEFAULT

Left Joy-Con Joystick Replacement

  • Insert an opening pick into the seam at the bottom edge of the controller (opposite the L and ZL buttons).Slowly slide the flat edge of your opening pick up the side of the Joy-Con.Be careful not to slide the opening pick too far inside the Joy-Con. This may damage the inner components. The back panel loosens fairly easily, so not much pressure is needed.
    • Insert an opening pick into the seam at the bottom edge of the controller (opposite the L and ZL buttons).

    • Slowly slide the flat edge of your opening pick up the side of the Joy-Con.

    • Be careful not to slide the opening pick too far inside the Joy-Con. This may damage the inner components. The back panel loosens fairly easily, so not much pressure is needed.

    Edit

  • With the charging rail facing away from you, open the the Joy-Con like a book.Don’t try to fully remove the back panel yet. There are still two cables connecting the charging rail to the motherboard.
    • With the charging rail facing away from you, open the the Joy-Con like a book.

    • Don’t try to fully remove the back panel yet. There are still two cables connecting the charging rail to the motherboard.

    Edit

  • Use a spudger to gently pry the battery connector straight up from its socket on the motherboard. This will keep the Joy-Con from powering on during the repair.Be very careful as you pry up the connector—if it doesn't come up with the spudger, try gently pulling the cables straight up from the board to disconnect it.
    • Use a spudger to gently pry the battery connector straight up from its socket on the motherboard. This will keep the Joy-Con from powering on during the repair.

    • Be very careful as you pry up the connector—if it doesn't come up with the spudger, try gently pulling the cables straight up from the board to disconnect it.

    • During reassembly, press the connector straight down into its socket on the board to reconnect the battery.

    Edit

  • Insert an opening pick between the battery and the Joy-Con housing.Gently pry out the battery, which is lightly taped in place.Be careful not to deform or puncture the battery—it can catch fire or explode if damaged.
    • Insert an opening pick between the battery and the Joy-Con housing.

    • Gently pry out the battery, which is lightly taped in place.

    • Be careful not to deform or puncture the battery—it can catch fire or explode if damaged.

    Edit

  • Remove the three 3.5 mm golden Phillips #00 screws from the midframe.
    • Remove the three 3.5 mm golden Phillips #00 screws from the midframe.

    • Do not attempt to remove the midframe yet. There is a fragile cable that still connects the ZL button on the midframe to the motherboard underneath.

    Edit

  • Carefully flip the midframe over, away from the motherboard, as if you were turning the page of a book.
    • Carefully flip the midframe over, away from the motherboard, as if you were turning the page of a book.

    • Do your best not to stress the thin ribbon cable attached to the ZL button during this step.

    Edit

  • Edit

  • Edit

  • Edit

  • Remove the two 3.5 mm Phillips #00 screws from the joystick.
    • Remove the two 3.5 mm Phillips #00 screws from the joystick.

    Edit

  • Carefully remove the joystick from its housing.There is a thin black gasket around the hole where the joystick pokes through the Joy-Con. Do your best not to disturb this gasket as you remove the joystick!
    • Carefully remove the joystick from its housing.

    • There is a thin black gasket around the hole where the joystick pokes through the Joy-Con. Do your best not to disturb this gasket as you remove the joystick!

    • Once the Joy-Con is fully reassembled, connect it to your Nintendo Switch and calibrate the new joystick. Additionally, you may need to power cycle your Switch by holding down the power button for 10-15 seconds until it turns off, then turning it back on.

    Edit

  • Sours: https://www.ifixit.com/Guide/Left+Joy-Con+Joystick+Replacement/113182

    The Nintendo Switch is perhaps the most unique video game console ever created. It can function as both a traditional console and a handheld game system. This makes it easily portable, while still allowing 1080p graphics on your big-screen TV. As a result, it should come as no surprise that it’s sold over 52-million units to date. With sales still going strong, there’s no telling how the Switch will rank in terms of all-time sales. It probably won’t surpass the Wii’s 101-million units, but nonetheless, it’s still performed marvelously.

    Of course, like every game system, things inevitably break down during use. And one of the most common failures is the thumbsticks. Again, this should not be surprising. You’re constantly handling them and moving them around. Eventually, the padding is going to wear off the top. When this happens, particularly when the wear is uneven, it can be a major problem. In the past, we’ve reviewed several different Switch accessories. These include charging stations to keep your battery full, as long as controller clip mounts for more ergonomic handheld play. We’ve even reviewed car headrest mounts so you can keep the little ones entertained on the road.

    replace-nintendo-switch-joycon-thumbstick

    Today, we’re going to review three of the best Nintendo Switch replacement thumbsticks available. First, we’ll review the Imncya Replacement Joystick. This is a set of four replacement thumbsticks, with reduced drift and improved calibration. Next, we’ll look at the Veanic 3D Replacement Joystick. This two-pack sports a similar design, along with all necessary installation hardware. Finally, we’ll check out the Wu-Minglu Joystick Replacement Kit. This kit includes metal locking buckles, along with a set of fun decorative stickers. Which one is the best? Let’s take a closer look, and see how well they compare!

    How to Replace Nintendo Switch Thumbsticks

    So, how does one go about replacing their Nintendo Switch thumbsticks? Before we continue, we should mention that performing a repair yourself will void your warranty. If you’re still under warranty, the best thing to do is file a claim with Nintendo. That said, if your warranty has expired, what have you got to lose? You either replace your thumbsticks, or you buy a brand new set of JoyCons. Here’s how it works.

    First, you’ll need to get your hands on a Y00 tri-wing screwdriver. You’ll also want a PH00 Phillips screwdriver. A nylon spudger and plastic pick are also advisable, but not required. They definitely make the job easier, though.

    To begin with, you’ll want to remove the four Y00 screws from the back of your JoyCon controller. These screws are very small and easy to lose. As a result, it’s a good idea to use a magnetic dish, or at least a small bowl, to keep them organized. Once the screws are removed, use your pick to open up the seam in the edge of the controller. The best spot for this is on the opposite edge from the L and ZL buttons, where it will pry open easily. You can use a small flathead screwdriver if necessary, but keep in mind that this will mar your plastic.

    Slide your pick or screwdriver up the side of the controller to widen the gap. As you go, make sure not to push it too far into the guts of the controller. This can damage wires or other internal electronic components. The back panel should open without a lot of pressure, so take it easy. Once it’s loosened up, the controller should open up like a book. At this time, it’s important that you don’t fully remove the back panel. The front and back panels are still connected by a pair of charging ribbons.

    replace-nintendo-switch-joycon-thumbstick

    Use a nylon spudger to carefully disconnect the charging ribbons from the battery. A screwdriver will get the job done. However, we should stress, this can cause damage. If you slip, you can easily ruin the ribbons for good. At this point, the front and back panels will easily separate. Use the same spudger to remove the battery’s charging wires from the motherboard. They will pry directly upwards, which will prevent the controller from accidentally powering on. Sometimes, these connectors can be a pit tight. If that’s the case, try rocking the spudger gently from side to side to loosen them up. When you’re reassembling the controller, the connectors should press down easily.

    Next, you’ll need to remove the battery. The best way to do this is to carefully insert a plastic pick behind the battery, and gently pry it out. Be very careful when doing this. If you damage the battery housing, it’s going to need to be replaced. There’s a small piece of tape holding the battery in place. If it doesn’t pry loose easily, you’ll need to carefully cut the tape.

    Once the battery is removed, you’ll see a middle plastic panel that covers the motherboard and joystick. It’s held in place by three PH00 Phillips screws, which will need to be removed. With the screws out, carefully fold the middle panel open. It has a small power ribbon running through it, which you don’t want to damage in the process. With the motherboard revealed, unplug the power ribbon that connects the panel to the motherboard. You can do this either with a spudger or with a fine pair of tweezers.

    replace-nintendo-switch-joycon-thumbstick

    Now the motherboard will be unobstructed. However, there will still be a ribbon cable obstructing the back of your thumbstick. Use a spudger to unplug this cable, and you’re ready to change out the actual thumbstick. Pry open the thumbstick’s ribbon connector lock, and remove the cable. Next, you’ll find two PH00 Phillips screws holding the thumbstick in place. Remove these screws, then carefully lift out the thumbstick. The thumbstick is surrounded by a black rubber gasket that helps hold it in place. Try not to damage this gasket while you’re removing the thumbstick.

    That about covers it! Drop in your new thumbstick, and reassemble your JoyCon controller. The whole process should only take about half an hour. As repairs go, that’s about as easy as it gets.

    Imncya Replacement Joystick

    Imncya Replacement Joystick

    The Imncya Replacement Joystick is a four-pack of joysticks that are virtually identical to the original Switch thumbsticks. With this kit, you can replace the thumbsticks on two sets of JoyCon controllers. They’re easy to install, and the kit includes all necessary hardware. One minor quibble is that the kit only includes six replacement screws. To be fair, if you’re careful, you shouldn’t need any of them. But keep in mind that there are only enough for three thumbsticks, not four.

    The thumbsticks themselves are reinforced with metal, which makes them a bit sturdier than the originals. Along with the thumbsticks themselves, you also get all the tools you need for installation. You get a Y00 tri-wing screwdriver for the case. You get a PH00 screwdriver for the internal components. You also get a plastic pick, a spudger, and a pair of tweezers. There are even red and blue thumbstick caps that allow you to add a splash of color.

    The Imncya thumbsticks are very well-engineered, and shouldn’t drift at all. However, as with any new thumbsticks, you’ll need to calibrate them after installation. You can do this from your Switch’s menu, and it takes just a few minutes.

    Veanic 3D Replacement Joystick

    Veanic 3D Replacement Joystick

    In most respects, the Veanic 3D Replacement Joystick is similar to the IMncya kit. It comes with a single pair of joysticks rather than two pairs, but it’s correspondingly more affordable. You get four screws for installation, along with a pair of screwdrivers, tweezers, a spludger, and a plastic pick. There’s also a pair of alternative thumbstick caps. These caps have a bit more texture, and provide superior grip. This gives you a bit of customization if you want a different feel. And like the Imncya joysticks, these are reinforced with metal, providing better durability and stability.

    Wu-Minglu Joystick Replacement Kit

    Wu-Minglu Joystick Replacement Kit

    The Wu-Minglu Joystick Replacement is a pair of thumbsticks, suitable for repairing a single JoyCon controller. Both joysticks are very well-engineered. They’re metal-reinforced, which provides more durability than the originals. However, the metal reinforcement isn’t limited to the joysticks themselves. The locking buckles are also constructed from metal. This won’t matter much during use, but it makes a big difference during installation. Because the buckles are so strong, they won’t get damaged while you’re plugging them in. Not only that, but the kit includes 24 colorful, patterned stickers for decorating your thumbsticks. The stickers will wear off in time, but they do add a fun touch to an otherwise mundane part.

    The kit includes parts not just for installing a new thumbstick, but for servicing your entire Switch. You get a Y00 and Y02 driver, along with a PH00 Phillips driver. The drivers are well-constructed, with textured barrels that sport a curved profile. This makes them ergonomic and easy to grip. Moreover, the backs of the handles rotate freely, which makes operation very easy. You get a plastic pick, a nylon spludger, and tweezers for assembly. There’s also a small brush for dusting your controller, and a small screen wipe for eliminating finger smudges. Finally, you get a suction cup, two extra plastic picks, and even a small plastic case for your screws. If you want everything you need in a single package, you’re looking at an excellent kit.

    All of this comes with Wu-Minglu’s 90-day money-back guarantee. If there are any issues during installation, simply return them for a full refund.

    Final Verdict

    Each of these Nintendo Switch replacement thumbsticks brings a lot to the table. To begin with, the Imncya Replacement Joystick is an ideal choice for repairing more than one controller. In addition, the thumbsticks are very well constructed, so you won’t have issues with durability. The Veanic 3D Replacement Joystick is similar in most respects. However, the alternative caps provide for better grip if you prefer a stickier stick. Finally, we looked at the Wu-Minglu Joystick Replacement Kit. This kit comes with extra hardware for working on your main Switch unit. It also sports metal locking buckles, so it’s less likely to get damaged during installation.

    Was this helpful? Please consider sharing:

    Sours: https://nerdtechy.com/nintendo-switch-replacement-thumbsticks
    1. Subaru forester reviews by year
    2. 2013 lincoln mks ecoboost problems
    3. Hotels on north monroe street
    4. Iphone purse with touch screen

    Nintendo Switch owners have been experiencing problems with the console’s removable Joy-Con controllers for years now, with users reporting weird joystick drifting problems that cause false inputs and have been steadily growing over time as original Switch machines grow older.

    Ever since a report by Kotaku from July 2019 shined a light on the Joy-Con drift issue, Nintendo has changed its policies significantly. The company will now repair drifting Joy-Con controllers for free, even if your controllers are outside the regular warranty. But Nintendo hasn’t changed the design of the controllers, and it’s still an issue today, even on the refreshed Switch models that launched last year.

    If you’re looking for more information on the problem, here’s the current situation:

    What is “Joy-Con drift”?

    Joy-Con drift is an issue that Switch owners have been encountering over the last few months that causes the analog sticks on the controllers to randomly move around and input commands to the console, even when they’re not being physically moved.

    Anecdotally, the issue seems to affect left Joy-Con controllers (which tend to be used for movement in most games) more than the right half of the controller set. Although, there are reports of users experiencing it on both joysticks. A quick (and extremely unscientific) poll of Verge staffers revealed that some Switch owners have reported multiple controllers encountering the issue, while others have never experienced it, which seems to be mirrored by reports around the internet.

    What causes Joy-Con drift?

    There are two potential causes for drift: some users blame the issue on either dust or debris making their way into the controller underneath a rubber cap that’s designed to keep the interior clean.

    Others have completely disassembled the controller and found worn-down contacts, which might be causing the issue due to repetitive use. It’s also possible that neither of those theories is correct or that it’s a combination of factors that cause stick drift over time. Without Nintendo clarifying the situation, it’s tough to tell exactly what’s wrong.

    How do I fix the issue?

    As mentioned above, it’s not fully clear what’s causing the issue, which makes fixing it tricky. A possible solution is to make sure you’re running the latest Switch software or to recalibrate your analog sticks to make sure it’s not a software issue.

    Some users have also tried using compressed air or isopropyl alcohol to fix the problem, although success seems to vary greatly. Others have taken the more drastic step of fully replacing the joystick entirely — a far more difficult fix that will void your warranty, if it works at all.

    What is Nintendo doing about impacted controllers?

    Following the outrage over the issue in July 2019, Nintendo has begun to fix impacted controllers free of charge. Vice News reports that Nintendo has directed its customer support team to fix Joy-Con controllers for free and issue refunds for previous repairs, even if you’re no longer under warranty.

    Nintendo now even has a dedicated area of its support website for Joy-Con repair requests: just fill out the form and Nintendo will coordinate your return, confirm that the controllers have the issue, and either repair or replace the controllers.

    Otherwise, Nintendo offers a standard warranty of 90 days (for accessories, which seems to include separately purchased Joy-Con controllers) and 12 months (for consoles, which seems to include Joy-Con controllers that are included with a Switch).

    If you’re outside the warranty, Reddit users had previously reported costs of $40 for an out-of-warranty repair, which is nearly the cost of a replacement single Joy-Con controller. (They run for $50 individually or $80 as a pair.) As of now, there haven’t been any announcements of an extended warranty for controllers.

    When the issue was first revealed, Nintendo commented:

    At Nintendo, we take great pride in creating quality products and we are continuously making improvements to them. We are aware of recent reports that some Joy-Con controllers are not responding correctly. We want our consumers to have fun with Nintendo Switch, and if anything falls short of this goal we always encourage them to visit http://support.nintendo.com so we can help.

    Is anyone suing Nintendo?

    Back in 2019, law firm Chimicles Schwartz Kriner & Donaldson-Smith filed a class action lawsuit against Nintendo, alleging that the Joy-Con controllers are defective due to the drift issues, and the firm is actively seeking more Switch owners to join the suit. That suit is still in progress, with the firm recently requesting that users send in videos of drift to help prove to Nintendo that the issue has caused problems for customers.

    Additionally, a second class action suit has been filled in California over the same issue in October 2020.

    Is drift a problem on the Switch Lite?

    It’s unclear if the Switch Lite is as affected when it comes to controller stick drift — reports from across the internet vary, and there doesn’t seem to have been the same level of outcry (or a Nintendo replacement program) for the smaller Switch model. But the Switch Lite doesn’t have removable controllers, so if it does suffer from similar issues with stick drifting, the situation could be far worse. In that scenario, users won’t be able to swap out a controller to fix it.

    Does the OLED Switch fix Joy-Con drift?

    Nintendo refuses to confirm one way or the other if the newly announced OLED Switch will feature design changes to fix Joy-Con drift more permanently, but it’s not looking good. In a statement provided to The Verge, the company said that “Joy-Con controller configuration and functionality did not change with Nintendo Switch (OLED model),” while an FAQ posted to its UK website notes that “the Joy-Con controllers included with Nintendo Switch (OLED model) are the same as the controllers currently available.”

    That all seems to indicate that the OLED Switch’s controllers are the same hardware as the existing Switch controllers, albeit in a new white color scheme. If that’s the case, then they’ll likely be susceptible to the same Joy-Con drift issues that existing models face.

    Update, July 24th, 2019: Added info Nintendo may be quietly fixing Joy-Cons with this issue for free.

    Update, October 6th, 2020: Added updated information on the current state of Joy-Con drift issues, Nintendo’s repair policy, and a new class action suit against the company.

    Update, July 13th, 2021: Added information on the OLED Switch.

    Sours: https://www.theverge.com/21504741/nintendo-switch-joy-con-drift-problem-explained
    LEFT Nintendo Switch Joycon Analog Replace - Fix Repair your broken or Drifting Joy-Con Controller

    Entering the woman, he grabbed her sides and began to move his pelvis. Dima with a camera approached them and filmed like a teenager's penis, then appeared and disappeared into Irina's vagina. The excitement of the teenagers was great, so the Roma finished a minute later.

    Next - he triumphantly shook off the rest of the sperm on Irina's stomach.

    Replacement left joy con joystick

    And now the first month of autumn is over, now is the golden time of "Indian summer". And a rhyme about this: Autumn shone with colorful flowers, Each leaf sparkled in the sun. It doesn't matter that nature has faded a little, The main thing is that it will be reborn again.

    Fix Your Nintendo Switch JoyCon Drift In 30 Minutes Or Less

    Not here. Marina slowed him down. She took out her phone.

    Now discussing:

    She was riding in the elevator, and she was bored alone. She was very excited and did not recognize herself today. She was ready to pounce on a young stallion.



    1011 1012 1013 1014 1015