Home depot wood counter top

Home depot wood counter top DEFAULT

Does Home Depot install Butcher block countertops?

Countertops installed by the professional contractors at The Home Depot. Replace your old kitchen countertops with quartz, granite, solid surface, laminate and more.

Click to see full answer.


Regarding this, how much does Home Depot charge for countertop installation?

Cost range: $50 to $90 per sq. ft. Average cost: $68 per sq. ft.

Similarly, is butcher block countertop expensive? In general, custom-made quality butcher block countertops range from $75 to $150 per square foot. In other words, good butcher block is more expensive than mid-range granite but less expensive than top-of-the-line natural stone.

Furthermore, is it hard to install Butcher block countertops?

Installing a butcher block countertop isn't difficult, but does require a circular saw and jigsaw. The simplest method, which we did, lines up the countertop in an L shape rather than using an angled corner (much more difficult!).

Do you glue down Butcher block countertops?

Butcher Block Surfaces should never be glued down with silicone caulk or construction adhesive as this will prevent natural movement and result in damage to the top. Cracking and warping when tops are installed using construction adhesive or silicone caulk will not be covered under warranty.

Sours: https://askinglot.com/does-home-depot-install-butcher-block-countertops

Your local Home Depot store's kitchen design center can partner with you to purchase and to cut the piece of countertop you'd like. You didn't specify what material you'd like the countertop to made from (laminate, Corian, natural stone, etc.), so this can greatly affect the price and how it can be cut.


Click to see full answer

Similarly, it is asked, will Lowes cut countertop for you?

Tape the cut line and use a fine tooth blade. Look and see if there is not a company in your area that will cut the counter top for you. Sometimes they will take the Lowe's countertop and cut it to your specifications. That will take the pressure off the contractor.

One may also ask, can you just replace countertops? "If you simply can't do both at once and just want to freshen up the aesthetics of your cabinetry later on, refacing your existing cabinets is the best option and will give you the look of brand new cabinetry without having to remove (and risk breaking) your new countertop."

Similarly, it is asked, how much does it cost to cut countertops?

Solid Surface Countertop Choices

MaterialPriceWith Installation
Engineered Stone Quartz$15-$70$25-$100
Corian$20-$75$30-$105
Acrylic$13-$30$23-$60

Does IKEA cut countertops to size?

Did you know: All countertops at IKEA are ready to be picked up at any time in the store. Plus, they can be cut to the length you want and you'll get 2 edging strips with each slab to cover-up any necessary seams. As a nice bonus, every single option even comes with a 25 Limited Year warranty.

Sours: https://findanyanswer.com/does-home-depot-cut-countertop
  1. 2020 toyota 4runner oil filter
  2. How to style sheer curtains
  3. 4 panel room divider wood

After being eclipsed by showy stones like granite and marble and maintenance-free engineered materials like quartz and solid surfacing, natural-wood countertops are enjoying a real revival. Constructed from pieces of hardwood laminated together with glue for strength and stability, they provide a warm, organic landing surface in a kitchen, one that is wonderfully forgiving, gentle on dishware, and able to absorb the noise of a busy household. Wood can also be revived if damaged; if it gets dinged, stained, or gouged, you can refinish it.

Why go with wood countertops?

The majority of wood countertops are made from traditional butcher block, and while they may see some mild meal prep, they’re rarely used for chopping these days. They’re favored more for their looks. Less expensive woods often line the kitchen as a handsome, budget-friendly surface; pricier species top islands or breakfast bars, where they provide a welcome textural contrast or a furniture-like finish.

The variety of woods available is impressive, from subtly grained maple to deep, rich walnut to dramatic mesquite to exotic iroko. Yes, wood is a good choice, but it does require some attention. This Old House’s guide to buying, installing, and maintaining these countertops will ensure that the surface you select will look and perform beautifully for years.

Butcher-Block Backstory

Getty

Up until the 1880s, butchers worked on thick rounds of sycamore, which were prone to splitting. In the early 1900s, it was discovered that pieces of hard maple glued together in big blocks provided a stronger, more durable surface that better stood up to meatcutters' cleavers.

Wood Countertops Key Questions Answered

What do they cost?

From $12 to more than $200 per square foot, uninstalled, depending on species, thickness, construction, and finish; add 5 to 10 percent more for most factory finishes.

Do they hold up?

Properly installed and cared for, wood countertops can last as long as you live in your home. Factory finishes generally come with a warranty. It can range from one year to a lifetime—and may only cover glued-joint separation.

DIY or hire a pro?

A homeowner comfortable with cutting and matching can install them in a weekend (making sink and faucet cutouts may void any warranty). For a pro install, add $8 per square foot, minimum.

Where to buy?

Order from kitchen showrooms and custom retailers or shop at home centers and big-box stores.

Wood Kitchen Countertop Pros

Alex Hayden

They lend character and lasting good looks, but they also need some TLC. Weigh the facts before investing:

  • They can be budget-friendly. A butcher-block counter made from birch or beech can cost little more than laminate and less than half the starter price for natural stone or engineered materials.
  • They can be easy to install. DIYers can cut prefab butcher-block tops to fit around corners, sinks, and appliances much more easily than most stone. Finishing wood is even more straightforward.
  • They're strong—and soft. Unlike with stone, there's no clatter when you set down a plate or a glass, and dropped dishes are less likely to break. Wood also quiets the whir of appliances, while stone will amplify such noise.
  • They can be refinished. Knife scratches, deep gouges, even burn marks can be sanded out and a DIY finish restored to look brand-new.
  • They're green. Most companies offer sustainably grown, Forest Stewardship Council-certified woods, including exotics. And while wood counters last for years, once worn out, they can be recycled.

Similar to shown: 1½-inch edge-grain teak; about $175 per sq. ft., uninstalled; devoswoodworking.com

Wood Kitchen Countertop Cons

iStock
  • They move. All wood expands and contracts with changes in atmospheric moisture, so there is the potential for these countertops to cup, warp, and gap if not properly constructed, installed, and maintained. The thicker the counter, the more stable it will be.
  • They require maintenance. Unfinished wood counters need monthly oiling. DIY clear-coated surfaces may require refinishing every five years or so. Factory-finished counters may never need recoating, but if they do, you'll pay to ship them, even under warranty.
  • They demand a watchful eye. Liquids can penetrate wood, causing stains, cracks, and joint separation—vinegar can actually dissolve glue—so spills, especially water around the sink, should be wiped up right away.
  • They're not fireproof. Wood and stove burners don't mix; check with your stove maker for required clearances. To prevent scorching, use trivets under hot pots.

How They're Made

Arthur Mount

Edge Grain

The most common type of butcher block is made from boards placed on their sides and glued so that the narrower edge forms the surface. The strips may be continuous lengths with no joints, or random- length pieces that are finger-jointed.

Best for: Large areas, like a long kitchen counter or island top. Because wood only moves in one direction, across its width, edge-grain butcher block is more stable than other wood countertops. It can also be less pricey.

End Grain

Blocks of edge-grain wood are turned on end to form a grid that's glued together. End-grain butcher block requires more wood and labor, so you'll pay about 40 percent more than for edge grain.

Because it’s also more prone to movement, end grain is often thicker, to counteract cupping and warping.

Best for: Cutting on, since end grain is easiest on knives and least likely to show blade marks. Now favored more for its checkerboard look than its functionality.

Face Grain

Also known as flat grain or plank grain, 4- to 12-inch-wide boards are laid flat and edge-glued, forming an almost seamless surface that highlights the natural patterns in the wood.

This may expose soft areas in the grain, making these tops more likely to show scratches, dents, and dings.

Best for: Dining islands, table and bar tops, desks—wherever you want a fine-furniture appearance, not a workhorse.

Wood Types, Choices, and Textures

Note: All prices are for 1½-inch-thick butcher block, uninstalled, except as noted.

Lisa Shin

Birch

These edge-grain samples showcase just 10 of the more than 40 hardwoods available today.

Price: $12 per sq. ft.

Maker:IKEA; sold only as a 1⅛-inch-thick prefab top.

Highlights: Neutral, light-colored wood with a fine grain.

American Walnut

Price: $60 per sq. ft.

Maker:John Boos & Co.

Highlights: Prized for its rich chocolate colors and striking black grain; perfect as an accent piece on an island.

Lisa Shin

Mesquite

Price: $151 per sq. ft.

Maker:DeVos Custom Woodworking

Highlights: Hardest domestic wood. Mineral streaks add character to reddish-brown strips.

Brazilian Cherry

Price: $115 per sq. ft.

Maker:The Grothouse Lumber Company

Highlights: Hardest of the woods shown, this fine-grain exotic is tough to scratch or dent.

Lisa Shin

Iroko

Price: $115 per sq. ft.

Maker:The Grothouse Lumber Company

Highlights: An African import; bright gold boards mellow in time to a teak-like brown.

Bamboo

Price: $98 per sq. ft.

Maker: Heirloom Wood Countertops, sold at The Home Depot

Highlights: Imported grass; heat-treating can give it a caramel hue.

Lisa Shin

Bolivian Rosewood

Price: $200 per sq. ft.

Maker:The Grothouse Lumber Company

Highlights: Dense, heavy, variegated wood with black stripes on a rich brown background.

Hard Maple

Price: $40 per sq. ft.

Maker:John Boos & Co.

Highlights: Classic butcher-block material that is exceptionally strong, with a straight, uniform grain.

Lisa Shin

White Oak

Price: $12 per sq. ft.

Maker: Williamsburg Butcher Block Co.; sold at Lumber Liquidators only as a prefab top.

Highlights: Showy grain on warm brown strips.

Saxon Wood

Price: $150 per sq. ft.

Maker:The Grothouse Lumber Company

Highlights: New South American find; yellow-brown wood with gray and black streaks.

Give It an Edge

Wood is easily tooled, so it lends itself to intricate designs. Here are standard edge profiles as well as a few fancier variations.

Lisa Shin

Roundover

This simple, classic profile (also called an eased edge) is slightly rounded. It goes with any style interior and makes sweeping up crumbs a breeze.

Sample edge profiles: DeVos Custom Woodworking

Chamfer

Also known as a beveled edge, this profile boasts a bold angle that works for contemporary as well as traditional kitchens.

Lisa Shin

Large Roundover With Fillet

A steeply rounded edge with a decorative ridge, typically 1/16 to ¼ inch high. An elegant, traditional look that requires a little more attention when cleaning.

Ogee

An edge that curves in and then out, somewhat like an S. This version is topped with a fillet for added dimension.

Large Roman Ogee

The S-curve is reversed, and the steep arc lends a more formal look.

The Slab Look

Lisa Shin

A single slice of wood, often with a live edge that follows the contours of the tree, is a sought-after look for a counter that doesn't see heavy use. But slabs' variable density and limited supply make them impractical in a kitchen. Search online for custom and specialty suppliers or find a local woodworker to source and install one.

Tips to Help You Shop Smarter

iStock
  • Look for solid wood. Avoid particleboard or MDF with wood veneer, which can swell when exposed to moisture and limits sanding to fix stains or nicks.
  • Measure correctly. To get an accurate price, measure the tops of your base cabinets, then factor in the overhang you want; 1 to 1½ inches is typical. On an island, a 12- to 16-inch overhang allows for pulling up stools.
  • Inspect for gaps. Joints between strips or boards should be minuscule and consistent. If there are noticeable gaps, it's more likely they'll open up farther, becoming noticeably unglued.

Finish Options

Lisa Shin

A wood kitchen counter is incomplete without a food-safe protective coating on all sides and edges.

Oil

For a matte look and a food-safe surface you can cut on, use FDA-approved mineral oil. It seeps in to make wood moisture-, heat-, and stain-resistant. Or try a nonpetroleum-based walnut oil or a "curing oil," such as pure tung oil, that hardens to form an imperceptible film that will wear but won't peel.

Oil-Wax Blend

Made from mineral oil and beeswax or paraffin wax, this finish formula adds another layer of protection against moisture and helps seal the oil into the wood. Apply liberally with a clean cloth in the direction of the wood grain, let sit for 20 minutes, remove excess, and buff to a satiny finish.

Clear coat

Urethane, acrylic, or resin-curing-oil finishes provide superior protection against water, stains, and wear and are food-safe once fully cured. But reviving a worn or damaged top means stripping it and refinishing. Proprietary finishes offered by some companies cannot be matched but may never need recoating.

To Stain or Not to Stain?

Lisa Shin

Adding a stain can enhance the color and grain of a wood countertop, but you'll pay 5 to 10 percent more than you would for the same species in its natural state. You can get a pricey look for less, however, by choosing an inexpensive, light-colored species (such as beech) and staining it a rich color (like walnut).

To DIY, sand off any finish and use a lint-free cotton cloth or natural-bristle brush to apply the stain, then wipe off the excess. When dry, add a food-safe clear coat. But never use stained butcher block as a cutting surface.

Consider the Sink

Lisa Shin

For a water-resistant barrier, all cutouts, edges, and surfaces must be treated with your choice of finish to seal out moisture. "Undermount sinks are ideal with wood countertops," says Paul Grothouse, owner, The Grothouse Lumber Company. Cutouts that extend slightly beyond the sink lip and over the bowl prevent standing water from saturating the edge, making the counter easier to maintain.

Drop-in sinks work best with clear-coated or factory-finished countertops along with a flexible sealant beneath the rim to protect the wood. Avoid marine varnish; while water resistant, this high-VOC finish is not food safe.

DIY Wood Countertops Like a Pro

Lisa Shin

Use cardboard templates to trim prefab tops to size with a circular saw and a router, or send templates to a manufacturer; many will cut and ship slabs for free (cutouts and curves cost extra). On open-top base cabinets, fill with plywood fastening strips every foot; for solid-top cabinets, create air space with thin furring strips to allow moisture to escape. Center holes in the strips and drive a screw fitted with a fender washer up through each hole, into the countertop.

Find the full step-by-step at How to Install a Butcher-Block Countertop.

How to Maintain Wood Countertops

Kolin Smith

Clean and Sanitize

Wipe down the surface daily with a damp cloth and a small amount of dish soap; follow with a clean, damp cloth. To de-germ, spritz with a solution of 1 part white vinegar to 4 parts water; let sit for 10 minutes, then wipe away. Avoid harsh cleansers with ammonia or bleach, which can eat away the finish and raise the grain.

Remove Stains and Odors

Sprinkle the affected area with a generous amount of table salt and rub it in with a lemon quarter, squeezing juice on the counter-top as you go. Let the mixture sit for a few minutes, then wipe with a clean, damp cloth.

Hide Scratches and Burns

Rub on a colored paraffin-wax stick, such as FastCap Softwax, in a shade that matches the wood. Remove excess with a plastic scraper and buff with a cloth. To remove deeper cuts and burns, begin with a coarse sandpaper, step up to finer grits, and finish with a very fine grit; reapply oil or an oil-wax blend to finish.

Fill Spaces

Melt a 1-to-4 mixture of beeswax or household paraffin wax and mineral oil in a double boiler. Rub the warm mixture into any splits or cracks with a clean cloth to seal them.

Wood Counter Styles

Polished Traditional

Dominique Vorillon

With its rich color and fancy edge profile, this glossy island top looks at home with a marble backsplash and copper range.

Similar to shown: 2-inch iroko, about $153 per sq. ft.; jaaronwoodcountertops.com

Organic Classic

Sours: https://www.thisoldhouse.com/kitchens/21018085/all-about-wood-countertops
Butcher Block Finishing Tips – Hardwood Reflections

Home Depot sells a range of kitchen countertops such as laminate, granite, and marble countertops for renovation and renewal projects.

However, customers looking to purchase countertops may be wondering – does Home Depot cut countertops as well? Here is what I’ve discovered about this through my research!

Does Home Depot Cut Countertops In 2021?

Home Depot can cut and install laminate, butcher block, granite, and marble countertops if they are purchased from Home Depot as of 2021. Alternatively, customers can purchase or rent circular saws from Home Depot to cut kitchen countertops at home. Competitors such as Lowe’s also offer this service.

If you want to learn more about how much Home Depot charges for cutting countertops, what kind of countertops Home Depot can cut, and much more, keep on reading!

How Much Does It Cost To Cut Countertops At Home Depot

The cost of cutting countertops at Home Depot depends on the complexity of your measurements.

For example, you can expect to pay around $110 to cut out a cooktop. Home Depot typically charges $20 for a single faucet cut out and $25 to cut around electrical outlets.

Does Home Depot Cut Laminate Countertops?

Home Depot will cut laminate countertops that customers purchased directly from the kitchen design center.

An installation specialist will cut the laminate countertops according to the measurements you provide and shipped directly to you as part of the kitchen unit installation service.

Note, you only receive this when you buy a full kitchen unit from Home Depot.

Customers should note that Home Depot cannot cut laminate countertops that you have purchased separately as the retailer does not cut countertops in-store.

Alternatively, Menards offers a similar service. Firstly, take accurate kitchen measurements, design your laminate countertops, and place the order at your local store.

Does Home Depot Cut Butcher Block Countertops?

Home Depot does not install butcher block countertops through their kitchen installation service and, therefore, does not cut them.

However, if you require a particular length, you may contact the Home Depot kitchen department for further information on processing a special order.

For a more accurate service, you may consider buying and installing your butcher block countertop from IKEA.

During the installation service, IKEA can cut butcher block countertops according to your measurements.

Does Home Depot Cut Granite Countertops?

If you choose to install your kitchen with granite countertops through Home Depot, they will enlist a third-party contractor to cut the material to suit your unique measurements.

Unfortunately, Home Depot does not cut granite countertops at any of its store locations or countertops that have been purchased individually.

Alternatively, Lowes includes granite countertop cutting in their installation service.

Simply fill out a form containing your requirements before meeting with a kitchen specialist to talk through measurements.

Once you have paid for the service, a designer will send a countertop template to the installers, who will cut your granite countertops to size.

Does Home Depot Cut Marble Countertops?

Home Depot will only cut marble countertops through their kitchen installation service.

Once the customer has finalized the final countertop design, a certified professional will arrange to visit your home and take accurate measurements of your kitchen space.

Next, your cut marble countertops will be delivered and installed by an insured contractor.

As with granite countertops, Lowes will gladly cut marble countertops through the installation service.

The total cost is calculated by the amount of marble you require (measures in square feet) and the intricacy of necessary cutouts.

Does Home Depot Sell Tools For Cutting Countertops?

For granite countertops, the top-selling products from Home Depot are the Makita X-LOCK Continuous Diamond Blade for Ceramic and Granite Cutting, costing $27.97.

It is compatible with angle grinders with a 7-8 inch arbor. You can also apply the Diablo Diamond Continuous Rim Cut-Off Discs to a 5-8 inch arbor for masonry in various inch sizes.

Some of Home Depot’s best-selling circular saws include the Dewalt 20-volt Circular Saw ($99) and the Makita 18-volt Circular Saw Kit ($349).

Employees at Home Depot can advise you on the best tools needed to cut the type of countertop you have.

Can You Rent Countertop Cutting Tools At Home Depot?

If you’re looking to cut durable materials such as marble, butcher block, or granite, you may wish to rent the Electric Circular Saw for $16 for four hours, $23 per day, $92 per week, and $276 for four weeks.

To look for available tools, enter your zip code into the search bar to see which devices are available for hire near you.

What Countertops Does Home Depot Sell?

Countertops from Home Depot are available in a range of colors and materials, including butcher block material and wood such as maple, birch, and walnut.

Along with that, Home Depot also offers countertops in materials such as quartz, quartzite, and granite, as well as laminate and marble.

All countertops from Home Depot vary in price depending on the style, color, and size required for your kitchen.

Note that Home Depot can also install countertops, charging around $27-$24 per square foot to install a countertop for you (on average).

In total, it can be around $1,000 for a laminate countertop to be installed by Home Depot, but this can vary depending on the countertop material.

How Much Do Home Depot Countertops Cost?

Prices for Home Depot countertops vary from around $35 to $1,500, depending on the material and amount required.

Theaverage prices for Home Depot countertop materials are as follows:

  • Quartz: $50 to $90 per square foot, on average $68 per square foot
  • Granite: $40 to $100 per square foot, on average $58 per square foot
  • Solid Surface: $37 to $67 per square foot, on average $52 per square foot
  • Laminate: $27 to $34 per square foot, on average $29 per square foot

There are also additional prices for finishes such as countertop edges (which are around $20), and corners (which are on average $60).

Other than that, Home Depot also sells a range of products to maintain and care for your countertops, such as oils and countertop cleaners.

If you want to know more about Home Depot’s services, you might also be interested in reading up on whether or not Home Depot cuts tile, if Home Depot installs dishwashers, and if Home Depot cuts metal sheets, pipes, and rods.

Conclusion: Does Home Depot Cut Countertops?

Home Depot will only cut laminate, granite, and marble countertops if purchased through the store’s installation service.

Home Depot does not install butcher block countertops, and therefore, it is not cut there. IKEA can cut and install butcher block countertops.

Alternatively, you can buy or rent tools such as a circular saw to cut your own countertop.

Sours: https://querysprout.com/does-home-depot-cut-countertops/

Counter top depot wood home

Moscow at night. morose driver. second floor. the light is on.

Home Depot kitchen counter install and review

The only thing I ever did and found disgusting. I rubbed his cock slowly until he rose. Moving my legs hard to please him with my work, I awkwardly spread my legs, presenting my son's eyes with an open pussy. The most delightful picture in the world - He groaned. What, footwork or my gaping pussy.

Now discussing:

Okay, let's get up. Although no, Id better lie still, Im in no hurry. I dont need to go to work, there will be holidays for another three days, I have no wives or children, the sun shines past the window and does.



1339 1340 1341 1342 1343