Napoleon gas fireplace log placement

6.4

LOG PLACEMENT

logs and glowing embers exclusive to Napoleon Fireplaces, provide a unique and realistic

TM

PHAZER

glowing effect that is different in every installation. Take the time to carefully position the glowing embers for a

maximum glowing effect.

Log colours may vary. During the initial use of the fi replace, the colours will become more uniform as colour

pigments burn in during the heat activated curing process.

6.4.2 Move the two small logs (#2 & #3) into

position, lining up the studs located on the

burner with the holes on the bottom of the

logs. Ensure that the small logs sit fl at on the

burner.

6.4.4 Position the base end of the center log (#5)

against the middle grate post with the other

end of the log resting in the pocket of the left

crossover log.

6.4.1 Place the back log (#1) onto the

SIDEVIEW

log support tray and in front of

the tabs. The tabs maintain an air

space between the log and

fi rebox back to facilitate

combustion air fl ow. Ensure that

the back of the log rests against

the brackets on the back wall of

TAB

the fi rebox.

6.4.3 Place the bottom of the left crossover log (#4)

against the left fi rebox side and pulled forward

to the grate.

The top of the log should rest in the pocket on

the back log.

6.4.5 Place the bottom of the right crossover log (#6)

against the right fi rebox side and pulled

forward to the grate. The top of the log should

rest in the pocket provided on the center log

(#5).

39

W415-0210 / S / 03.10.09

Add an instant upgrade to your old wood-burning fireplace. Instead of chopping wood and hauling logs, a flip of the switch will instantly ignite a realistic wood fire. While a professional will need to hook up this unique fireplace solution, there is no need for costly renovations when a Gas Log Set is chosen. They are simply installed into an existing wood fireplace opening. Gas Log Sets vent directly out of the existing chimney. Radiant heat from the logs and flames heat the space that they are installed and continue to do so until the logs have cooled. Relax in front of a roaring fire with the highest flames in the industry, as they dance among hand-painted realistic logs.

6.2

LOG PLACEMENT

LOGS MUST BE PLACED IN THEIR EXACT LOCATION IN THE APPLIANCE. DO NOT CHANGE OR MODIFY

FROM THE PROPER LOG POSITION, SINCE APPLIANCE MAY NOT FUNCTION PROPERLY AND DELAYED

The individual logs can be easily identifi ed by the numbers cast on the underside of each log.

Phazer

logs and glowing embers exclusive to Wolf Steel Ltd., provide a unique and realistic glowing effect

TM

that is different in every installation. Take the time to carefully position the glowing embers for a maximum

glowing effect. During the initial use of the appliance, log colours may vary. During the initial use of the appli-

ance the colours will become more uniform as colour pigments burn in during the heat activated curing pro-

cess.

Place the rear log (W135-0444) on rear bracket, ensure the log is

6.2.1

seated properly on the rear bracket and located on the center pin.

Place the charcoal strip log (W135-0448) on top of the grate aligning

6.2.2

the notches in the charcoal strip with the grate.

Align the hole in the bottom of the front left log (W135-0450) with the

6.2.3

screw and spacer on the left side of the burner. The middle of this log

rests against the charcoal strip.

Align the hole in the bottom of the front right log (W135-0451) with

6.2.4

the screw and spacer on the right side of the burner. The middle of

the log rests against the charcoal strip.

THE LOGS ARE FRAGILE AND SHOULD BE HANDLED WITH CARE.

WARNING

!

IGNITION MAY OCCUR.

31

W415-0869 / A / 06.10.10

20

W415-0547 / B / 05.08.06

LOGO

1.27cm

1.27cm

Remove the backing from the the logo and position onto the

control door as shown.

It is not necessary to remove the cast front, however, this

will make for a more simple log installation.

In order to assemble the log set, the door must be removed,

see Cast Front / Glass Door Removal in the FINISHING

section of this manual.

1. Place the rear log, as shown, onto the rear log support

brackets. Ensure the cutout on the left underside of the log,

fi ts over the pilot assembly . Bend the bracket on the right side

to help retain the rear log.

2. Place the hole in the underside of log #2 onto the locating

screw, on the left side of the burner. The fi bre burner is formed

to cradle the centre of the log.

3. Place the hole in the underside of log #3 onto the locating

screw, on the right side of the burner. The bottom branch of

log #3 sits infront of, and against, the right end of log #2.

4. Reinstall the glass door & front.

LOG LOCATING SCREWS

FIGURE 33a-d

BRACKET